<![CDATA[UiFlow Beta 1.4.1]]>Ver 1.4.1. time : 2019.10.12

  • 1: Add some HAT support（Servo、Servos、PuppyC、Joystick、BugC、Finger、BeetleC、YUN）.
  • 2: Add GPS Unit support
  • 3: Fixed some bugs.

updates_pic1
updates_pic2

]]>https://community.m5stack.com/topic/1380/uiflow-beta-1-4-1RSS for NodeWed, 29 Apr 2026 11:29:49 GMTSat, 12 Oct 2019 11:32:18 GMT60<![CDATA[Reply to UiFlow Beta 1.4.1 on Tue, 15 Oct 2019 05:36:08 GMT]]>@thrasher That page was hard to find and I discovered it late last night. I need to set up a test rig out in the workshop but until I can do that I am unable to test the RS485.

If I get anywhere I will post in the projects forum.

]]>https://community.m5stack.com/post/5972https://community.m5stack.com/post/5972Tue, 15 Oct 2019 05:36:08 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Mon, 14 Oct 2019 21:24:21 GMT]]>ajb2k3,
Sorry I didnt have chance to test today, Ive lost my max485 ic somewhere lol, cant connect m5stick anywhere else.
I looked through link but it needs testing, as far as I remember rs485 differs from rs232 as its a half duplex and I used to enter send/listen modes by pulling some pin up or down. Hopefully m5stacks unit does that for me with the code from the link because I cant see any interraction with control pins in the code

Thanks

]]>https://community.m5stack.com/post/5970https://community.m5stack.com/post/5970Mon, 14 Oct 2019 21:24:21 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Mon, 14 Oct 2019 19:56:06 GMT]]>@thrasher said in UiFlow Beta 1.4.1:

Thanks, I will give it a try tomorrow!

Just found something else
https://docs.m5stack.com/#/en/uiflow/RS485

]]>https://community.m5stack.com/post/5969https://community.m5stack.com/post/5969Mon, 14 Oct 2019 19:56:06 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sun, 13 Oct 2019 23:40:42 GMT]]>Thanks, I will give it a try tomorrow!

]]>https://community.m5stack.com/post/5951https://community.m5stack.com/post/5951Sun, 13 Oct 2019 23:40:42 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sun, 13 Oct 2019 19:17:37 GMT]]>@thrasher said in UiFlow Beta 1.4.1:

Yet no rs485 unit for stick-c in the list (:

OK To use the RS485 Hat you need to use the UART setup block and set TX =0 and RX = 26.

Sorry, taken me all day to workout the code blocks and convert a sample code briefly seen in a demo video.

]]>https://community.m5stack.com/post/5946https://community.m5stack.com/post/5946Sun, 13 Oct 2019 19:17:37 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sun, 13 Oct 2019 06:57:32 GMT]]>@Thrasher theres still a lot of RS485 work to be done and I'm tormenting the programmer over it.

@Mati Same here.

]]>https://community.m5stack.com/post/5931https://community.m5stack.com/post/5931Sun, 13 Oct 2019 06:57:32 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sun, 13 Oct 2019 06:39:59 GMT]]>nice, still waiting for PM2.5 SHT20 readings with is missing.

]]>https://community.m5stack.com/post/5930https://community.m5stack.com/post/5930Sun, 13 Oct 2019 06:39:59 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sat, 12 Oct 2019 15:22:50 GMT]]>Yet no rs485 unit for stick-c in the list (:

]]>https://community.m5stack.com/post/5922https://community.m5stack.com/post/5922Sat, 12 Oct 2019 15:22:50 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sat, 12 Oct 2019 12:17:21 GMT]]>@m5stack said in UiFlow Beta 1.4.1:

Ver 1.4.1. time : 2019.10.12

  • 1: Add some HAT support（Servo、Servos、PuppyC、Joystick、BugC、Finger、BeetleC、YUN）.
  • 2: Add GPS Unit support
  • 3: Fixed some bugs.

updates_pic1
updates_pic2

1.4.1 not is osburner software yet

]]>https://community.m5stack.com/post/5918https://community.m5stack.com/post/5918Sat, 12 Oct 2019 12:17:21 GMT<![CDATA[Reply to UiFlow Beta 1.4.1 on Sat, 12 Oct 2019 12:07:30 GMT]]>Looks like I have some updates to make

]]>https://community.m5stack.com/post/5917https://community.m5stack.com/post/5917Sat, 12 Oct 2019 12:07:30 GMT