<![CDATA[cardputer stuck on develop]]>just got my cardputer loaded apps and it bricked in black screen then added UIflow. Now it comes on but stuck on develop app when i open it it says private at top, mac#, email and web id to uflow2.stack.com/ but when i got there its just a older forum.any help on what to do what be appricated i really wanna play with it. oh when i go back and try to add any apps or erase there just errors and it wont let me do anything

]]>https://community.m5stack.com/topic/6442/cardputer-stuck-on-developRSS for NodeWed, 29 Apr 2026 01:29:15 GMTWed, 08 May 2024 07:57:00 GMT60<![CDATA[Reply to cardputer stuck on develop on Wed, 10 Jul 2024 01:24:33 GMT]]>@ROLF_STEINER
M5Stack documented this for each device. "Press G0 while booting...." or similar. Yes, I had problems too.

]]>https://community.m5stack.com/post/25803https://community.m5stack.com/post/25803Wed, 10 Jul 2024 01:24:33 GMT<![CDATA[Reply to cardputer stuck on develop on Sat, 06 Jul 2024 17:50:50 GMT]]>@ToxicAvenger hi i got a new core s3 and was not aware of this boot mode and the error was also occoring to me but on sync screen but on the core s3 to fix it i have to hold the reset button until ther green light turns on then only it started to upload new uiflow so for the cardputer it might be the same problem and also try using a diffrent usb cable.I was using wifi upload and it crashed during sync

software info and hardware
board : m5stack core s3
MCU : esp32s3 extenza lx7
uiflow vertion : 2.0.7
arduino ver : 2.1.0
windows 10

]]>https://community.m5stack.com/post/25770https://community.m5stack.com/post/25770Sat, 06 Jul 2024 17:50:50 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 06 Jun 2024 14:24:46 GMT]]>@ajb2k3 sure mate, after all, I redo all my steps and following the youtube video finally works.

many thanks and tons of likes!!

]]>https://community.m5stack.com/post/25516https://community.m5stack.com/post/25516Thu, 06 Jun 2024 14:24:46 GMT<![CDATA[Reply to cardputer stuck on develop on Fri, 17 May 2024 05:27:41 GMT]]>Have you installed ESP-IDF?

]]>https://community.m5stack.com/post/25304https://community.m5stack.com/post/25304Fri, 17 May 2024 05:27:41 GMT<![CDATA[Reply to cardputer stuck on develop on Fri, 17 May 2024 04:23:53 GMT]]>@rolf_steiner 0_1715919754111_e65ec64d-476a-4348-b3ba-5aa2e8278b4b-Captura de pantalla 2024-05-17 a las 00.16.41.png Captura de pantalla 2024-05-17 a las 00.16.41

0_1715919776087_d7f2a03d-e560-4cd2-8112-b037947185cb-Captura de pantalla 2024-05-17 a las 00.16.54.png Captura de pantalla 2024-05-17 a las 00.16.54

0_1715919798187_0042aa19-4ca4-42d3-9ac9-49e45cb656d8-Captura de pantalla 2024-05-17 a las 00.17.05.png Captura de pantalla 2024-05-17 a las 00.17.05

0_1715919817648_d392fe34-7bc3-41fa-a53c-753f7b2bfd19-Captura de pantalla 2024-05-17 a las 00.19.24.png Captura de pantalla 2024-05-17 a las 00.19.24

]]>https://community.m5stack.com/post/25303https://community.m5stack.com/post/25303Fri, 17 May 2024 04:23:53 GMT<![CDATA[Reply to cardputer stuck on develop on Fri, 17 May 2024 04:21:54 GMT]]>hi guys!!! same thing here too....
I used multiple cables (no result)
I updated softwares like a collector in a bunch of them...(same results)...
im absolutely lost....
so if someone see the light please share the trick...0_1715919681849_49fe5e9d-cbe7-4bf7-a20b-41c468144631-Captura de pantalla 2024-05-17 a las 00.16.41.png Captura de pantalla 2024-05-17 a las 00.16.41
Captura de pantalla 2024-05-17 a las 00.16.54
Captura de pantalla 2024-05-17 a las 00.17.05
Captura de pantalla 2024-05-17 a las 00.19.24

]]>https://community.m5stack.com/post/25302https://community.m5stack.com/post/25302Fri, 17 May 2024 04:21:54 GMT<![CDATA[Reply to cardputer stuck on develop on Fri, 17 May 2024 02:14:33 GMT]]>@ajb2k3 yea but still cant erase my sd and when i try to navigate anything in UI flow 2 it just doesnt work

]]>https://community.m5stack.com/post/25300https://community.m5stack.com/post/25300Fri, 17 May 2024 02:14:33 GMT<![CDATA[Reply to cardputer stuck on develop on Wed, 15 May 2024 18:17:13 GMT]]>@wilsoreal said in cardputer stuck on develop:

has anyone found a solution, i am having the same problem

Have you watched the video I linked to above?

]]>https://community.m5stack.com/post/25259https://community.m5stack.com/post/25259Wed, 15 May 2024 18:17:13 GMT<![CDATA[Reply to cardputer stuck on develop on Wed, 15 May 2024 02:09:33 GMT]]>has anyone found a solution, i am having the same problem

]]>https://community.m5stack.com/post/25246https://community.m5stack.com/post/25246Wed, 15 May 2024 02:09:33 GMT<![CDATA[Reply to cardputer stuck on develop on Fri, 10 May 2024 10:20:10 GMT]]>When in doubt, G0 and RST it out, hold G0 and tap RST and then let go of G0.

]]>https://community.m5stack.com/post/25178https://community.m5stack.com/post/25178Fri, 10 May 2024 10:20:10 GMT<![CDATA[Reply to cardputer stuck on develop on Fri, 10 May 2024 04:38:47 GMT]]>Does windows hardware manager or what ever its called show an error with the ports?

]]>https://community.m5stack.com/post/25165https://community.m5stack.com/post/25165Fri, 10 May 2024 04:38:47 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 20:27:46 GMT]]>@ajb2k3 when I do the reset with go and reset button before trying to burn it pops up a window show port5 then another saying port6. When I do anything after that it only gives option for port6 and nothing works on it

]]>https://community.m5stack.com/post/25161https://community.m5stack.com/post/25161Thu, 09 May 2024 20:27:46 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 19:59:20 GMT]]>Does Windows show any errors with the Com port?

]]>https://community.m5stack.com/post/25160https://community.m5stack.com/post/25160Thu, 09 May 2024 19:59:20 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 17:22:16 GMT]]>@ajb2k3 tried 4 different data cables, still same result. Do you think its defective or is it me?

]]>https://community.m5stack.com/post/25159https://community.m5stack.com/post/25159Thu, 09 May 2024 17:22:16 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 11:48:24 GMT]]>Try different cables. Not all cables are the same and some USBC cables don’t appear to work.

]]>https://community.m5stack.com/post/25153https://community.m5stack.com/post/25153Thu, 09 May 2024 11:48:24 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 08:02:59 GMT]]>@toxicavenger said in cardputer stuck on develop:

When i reset it says com 5 then com 6 then
--chip auto --port COM6 --baud 1500000 --before default_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x9000 C:\Users\lemstudent\Desktop\M5Burner-v3-beta-win-x64\packages\tmp\uiflow2-cfg.bin
esptool.py v4.6.2
Serial port COM6
Connecting...
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

A fatal error occurred: Failed to connect to Espressif device: No serial data received.
For troubleshooting steps visit: https://docs.espressif.com/projects/esptool/en/latest/troubleshooting.html

try to press and hold boot button for few seconds while plugging in usb to it .....and keep on/off in off position so m5stamp is powered up from usb not from battery

]]>https://community.m5stack.com/post/25149https://community.m5stack.com/post/25149Thu, 09 May 2024 08:02:59 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 05:11:40 GMT]]>When i reset it says com 5 then com 6 then
--chip auto --port COM6 --baud 1500000 --before default_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x9000 C:\Users\lemstudent\Desktop\M5Burner-v3-beta-win-x64\packages\tmp\uiflow2-cfg.bin
esptool.py v4.6.2
Serial port COM6
Connecting...
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.

A fatal error occurred: Failed to connect to Espressif device: No serial data received.
For troubleshooting steps visit: https://docs.espressif.com/projects/esptool/en/latest/troubleshooting.html

]]>https://community.m5stack.com/post/25146https://community.m5stack.com/post/25146Thu, 09 May 2024 05:11:40 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 05:04:09 GMT]]>@ajb2k3 -chip auto --port COM6 --baud 1500000 --before default_reset write_flash -z --flash_mode dio --flash_freq 80m --flash_size detect 0x9000 C:\Users\lemstudent\Desktop\M5Burner-v3-beta-win-x64\packages\tmp\uiflow2-cfg.bin
esptool.py v4.6.2
Serial port COM6

A fatal error occurred: Could not open COM6, the port doesn't exist

This is what i get when I try to

]]>https://community.m5stack.com/post/25145https://community.m5stack.com/post/25145Thu, 09 May 2024 05:04:09 GMT<![CDATA[Reply to cardputer stuck on develop on Thu, 09 May 2024 04:53:10 GMT]]>https://youtu.be/bnw0tPslV2o?si=jE61HjFvSB90atxy

]]>https://community.m5stack.com/post/25144https://community.m5stack.com/post/25144Thu, 09 May 2024 04:53:10 GMT<![CDATA[Reply to cardputer stuck on develop on Wed, 08 May 2024 17:48:52 GMT]]>@ajb2k3 whats your youtube and are you doing a video on how I can fix this issue, also when will your video be put on?

]]>https://community.m5stack.com/post/25138https://community.m5stack.com/post/25138Wed, 08 May 2024 17:48:52 GMT<![CDATA[Reply to cardputer stuck on develop on Wed, 08 May 2024 17:02:26 GMT]]>@toxicavenger UIflow 2 was updated a few weeks back but the engineers have been on tour
I am in the process of uploading a series of videos on installing UIFlow2 on YouTube

]]>https://community.m5stack.com/post/25137https://community.m5stack.com/post/25137Wed, 08 May 2024 17:02:26 GMT<![CDATA[Reply to cardputer stuck on develop on Wed, 08 May 2024 15:16:07 GMT]]>Total newbie here, I didnt erase before I added UIFLOW2. I do thinking i binded it . Everything I found on UIFLOW2 website looks like it was abandoned 2 years ago. Im signed into there forum. Is there any way i can reset this thing fresh and start over, what should I do?

]]>https://community.m5stack.com/post/25136https://community.m5stack.com/post/25136Wed, 08 May 2024 15:16:07 GMT<![CDATA[Reply to cardputer stuck on develop on Wed, 08 May 2024 10:44:21 GMT]]>Did you erase before burning UIFlow2?
Did you agree to bind the cardputer to your account?
Did you sign into M5burner with you forum details?
Are you sure you went to the UIFlow2 website?
Did you sign into UIFlow2 with you forum details?

]]>https://community.m5stack.com/post/25130https://community.m5stack.com/post/25130Wed, 08 May 2024 10:44:21 GMT