AtomDTU NB-IoT

[felmue]

Hello @Felix22

ok, his means your modem is alive and responding.

Now, please try the following commands (which are the same as are used in Init NB-IoT DTU) block, but we can see the responses of the modem:

You should get something like:

b'\r\nOK\r\n'
b'\r\nOK\r\n'
b'\r\nOK\r\n'
b'\r\n+CPIN: READY\r\n\r\nOK\r\n'
b'\r\n+CGCONTRDP: 1,5,"<YourAPN>","10.100.100.100.255.255.255.0"\r\n\r\nOK\r\n'

Thanks
Felix

[Felix22]

Yesterday i have made the similar with Arduino-C-Code and become as Response the carrier Code 28801 = Swisscom-Network but no response in q.beyond-Control-Panel...

I have tested with a complete new AtomDTU. Flash with v1.13.2

I think, no response :-((

[felmue]

Hello @Felix22

I just read in the q.beyond FAQ says that the SIM card needs to be activated.

I assume you did that already?

Thanks
Felix

[Felix22]

Yes, I have do it. She is activated.
The connection from 17.2.24 comes from a old iPhone

[felmue]

Hello @Felix22

ok, let's see what providers your modem can see.

Note: the last AT command AT+COPS=? can take a couple of minutes as it has to scan through all bands. (in my case it took about 3 minutes.)

Expected output:

b'\r\nOK\r\n'
b'\r\nOK\r\n'
b'\r\n+COPS: 0,2,"22801",9\r\n\r\nOK\r\n'
None
b'\r\n+COPS: (1,"SWISS GSM","SWISS","22801",9),(1,"sunrise","sunrise","22802",9),,(0-4),(0-2)\r\n\r\nOK\r\n'

Thanks
Felix

[Felix22]

:-)

[felmue]

Hello @Felix22

ok, so it seem that the modem is registered with Swisscom, but doesn't get an IP address since AT+COPS? succeeds, but AT+CGCONTRDP fails.

At this point I am not sure what might be the issue. Is there anything in the q.beyond portal, like a log showing some error?

Also since you used your iPhone with that SIM card before there might be some kind of security check not accepting a connection from a different device. On the q.beyond portal, is there a way to reset / clear the data from the previous connection?

Thanks
Felix

[Felix22]

Interesting, this is the response from the DigitalRepublic-SIM-Card how has no NarrowBand.
He see the Network also...

Now, ih have deactivated and new activated the SIM.

Now its a "3" = "Operator forbidden" (?) (Swisscom)
and
1 for sunrise

[felmue]

Hello @Felix22

hmm, strange. Do you know which roaming partner (Swisscom and/or Sunrise) q.beyond has in Switzerland for NB-IoT? Maybe worth checking with q.beyond support.

Thanks
Felix

[Felix22]

Many thanks.

I will write to the support from q.beyond.

If the connection will go on. What are the Code for an MQTT connection ?
If i become an IP-Address, can i use the "normal" MQTT Blockly ??

Regards,
Felix

[felmue]

Hello @Felix22

please refer to the SIM7020 documentation for MQTT commands. You can find the PDFs here - section Related Link.

As soon as the modem gets an IP address the last AT command AT+CGCONTRDP sent by Init NB-IoT DTU block should succeed and then you can use all the other MQTT blocks.

Thanks
Felix

[Felix22]

a.beyond say, she works in Switzerland with Swisscom NB.
How can I explicit connect to Swisscom (AT-Command) ?

[felmue]

Hello @Felix22

AT+COPS=1,2,"22801"

Thanks
Felix

[Felix22]

b'AT+CSQ\r\r\n+CSQ: 18,0\r\n\r\nOK\r\n'
men, i have a signal ?

b'AT+CSTT="iotsim.melita.io","",""\r\r\nOK\r\n'
b'AT+CSTT?\r\r\n+CSTT: "iotsim.melita.io","",""\r\n\r\nOK\r\n'
APN is set correct ?

b'AT+CGREG?\r\r\n+CGREG: 0,5\r\n\r\nOK\r\n'
Registered ?

b'AT+COPS: 1,2,"22801"\r\r\nERROR\r\n'
b'AT+COPS?\r\r\n+COPS: 0,2,"22801",9\r\n\r\nOK\r\n'

b'AT+CGACT?\r\r\n+CGACT: 1,0\r\n\r\nOK\r\n'

If i have a connection, do i become an ip-address ?
with the command AT+CIFSR

[felmue]

Hello @Felix22

it is my understanding that AT+CIFSR returns the local IP address in a TCP or UDP connection. (It's an AT command for compatibility with SIM800.)

See PDF document SIM7020 Series_TCPIP_Application Note_V1.04 - 6.2 TCP Client Connection. You'll find the link to the PDF here.

The way I use to set the APN is described in the same TCP/IP PDF - 3.2 APN Manual Configuration.

Thanks
Felix

[Felix22]

Result:

b'\r\nOK\r\n'
b'\r\nOK\r\n'
b'\r\nOK\r\n'
b'\r\nOK\r\n'
b'\r\nOK\r\n\r\n+CPIN: READY\r\n'
b'\r\n+CGREG: 0,5\r\n\r\nOK\r\n'
b'\r\n+CGCONTRDP: 1,5,"iotsim.melita.io","10.xx.xx.xx.255.255.255.0",,"212.xx.xx.xx","212.xx.xx.xx",,,,,1500\r\n\r\nOK\r\n'

Im a big step wider... now, i have become my ip address... :-)
Now i think... MQTT, next step.

[Felix22]

Juhuuuu !!
It works !
More Information and the solution will follow...

@felmue : many thanks

Felix

[felmue]

Hello @Felix22

I am happy to hear you got it working.

Thanks
Felix

[Felix22]

now, i have a new problem.
The mqtt broker test.mosquitto.test is working with my Blockly but my own Broker on my Server at home in a Docker container is not available from AtomDTU. But with a Internet Test Tool, it is working ( https://testclient-cloud.mqtt.cool/ )

I see no difference...
The orange part is working and the tree other is not working

• Domainname
• IP-Address
• Dyndns
  not working...
  test.mosquitto.org is working fine.

[felmue]

Hello @Felix22

hmm, that's a tricky one. Now that your modem gets an IP address; have you tried the official MQTT blocks?

Thanks
Felix